ThinkPad - Fehler-Codes (In Englisch)


Code Symptom or error Field replaceable unit or action, in sequence
0175 Bad CRC1, stop POST task.
The EEPROM checksum is not correct.

System board

0176 System Security. The system has been tampered with.
  • Run BIOS Setup Utility.
    Then save current setting by pressing F10.
  • System board
  • 0177 Bad SVP data. Stop POST task. System board
    0182 Bad CRC2. Enter BIOS Setup and load Setup Defaults. Run the BIOS Setup Utility and Load Setup Defaults
    0185 Bad startup sequence settings.
    Enter BIOS Setup and load setup defaults.
    Run the BIOS Setup Utility and Load Setup Defaults
    0187 EAIA data access error.
    The access to EEPROM has failed.

    System board

    0188 Invalid RFID serialization information area or bad CRC2.
    The EEPROM checksum is not correct.

    System board

    0189 Invalid RFID configuration information area.
    TThe EEPROM checksum is not correct.

    System board

    0190 Critical low battery error
  • Charge the battery pack
  • Battery pack
  • 0191 System Security.
    Invalid Remote Change requested.
  • Run BIOS Setup Utility.
    Then save current setting by pressing F10.
  • System board
  • 0192 System Security.
    Embedded Security hardware tamper detected.
    System board
    0195 Security hardware tamper detected
  • Enter BIOS Setup Utility by entering supervisor password. Then select Config, select Security Chip, and then select Clear Security Chip to clear this error.
  • Security chip
  • System board
  • 0196 Security hardware removed
  • Enter BIOS Setup Utility by entering supervisor password. Then select Config, select Security Chip, and then select Clear Security Chip to clear this error.
  • Security chip
  • System board
  • 0197 Invalid Remote change requested The remote configuration for the security chip has failed. Confirm the operation and try again.
    0199 System Security. Security password retry count exceeded.
  • Run BIOS Setup Utility.
    Then save current setting by pressing F10.
  • System board
  • 01C8 More than one modem devices are found.
    Remove one of them. Press ESC to continue.
  • Remove either a Mini PCI modem card or a modem daughter card; otherwise press Esc to ignore the warning message.
  • System board
  • 01C9 More than one Ethernet devices are found.
    Remove one of them.
    Press the Esc key to continue.
  • Remove either a Mini PCI Ethernet card or an Ethernet daughter card, other wise press the Esc key to ignore the warning message.
  • System board
  • 0200 Hard drive error. The hard drive is not working.
  • Remove and reinstall the hard drive
  • Load Setup Defaults in BIOS Setup Utility
  • Hard drive
  • System board
  • 021x Keyboard error

    Run an interactive tests of the keyboard and the auxiliary input device

    0220 Monitor type error.
    Monitor type does not match the one specified in CMOS.

    Load Setup Defaults in BIOS Setup Utility

    0230 Shadow RAM error.
    The shadow RAM failure at offset nnnn.

    System board

    0231 System RAM error. System RAM failure at offset nnnn.
  • DIMM
  • System board
  • 0232 Extended RAM error. Extended RAM failure at offset nnnn.
  • DIMM
  • System board
  • 0250 System battery error. System battery is dead.

    Replace the backup battery. Then run BIOS Setup Utility to reset the time and date.

    0251 System CMOS checksum bad. Default configuration used.

    Replace the backup battery. Then run BIOS Setup Utility to reset the time and date.

    0252 Password checksum bad.
    The password is cleared.

    Reset the password by running BIOS Setup Utility

    0260 System timer error
  • Replace the backup battery.
    Then run BIOS Setup Utility to reset the time and date.
  • System board
  • 0270 Real time clock error
  • Replace the backup battery.
    Then run BIOS Setup Utility to reset the time and date.
  • System board
  • 0271 Date and time error.
    Neither the date nor the time is set in the computer.

    Run BIOS Setup Utility to reset the time and date

    0280 Previous boot incomplete. Default configuration used.
  • Load Setup Defaults in BIOS Setup Utility
  • DIMM
  • System board
  • 02B2 Incorrect drive A type
  • Diskette drive
  • External FDD cable
  • I/O card
  • 02D0 System cache error

    CPU

    02F4 EISA CMOS not writable
  • Load Setup Defaults in BIOS Setup Utility
  • Replace the backup battery
  • System board
  • 02F5 DIMM test failure
  • DIMM
  • System board
  • 02F6 Software NMI failure
  • DIMM
  • System board
  • 02F7 Fail-safe timer NMI failure
  • DIMM
  • System board
  • 1801 Attached docking station is not supported Shut down the computer and remove it from the docking station
    1802 Unauthorized network card is plugged in.
    Power off and remove the Mini PCI network card.
  • Remove Mini PCI network card
  • System board
  • 1803 Unauthorized daughter card is plugged in.
    Power off and remove the daughter card.
  • Remove the daughter card that you installed
  • System board
  • 1804 Unauthorized WAN card is plugged in.
    Power off and remove the WAN card.
  • Remove the WAN card that you installed
  • System board
  • 1810 Hard drive partition layout error
  • If the Access IBM Predesktop Area has been previously disabled, go the the BIOS Setup Utility by pressing F1 to open the BIOS Setup Utility. Select Security, select Predesktop Area, and then select Access IBM Predesktop Area. Set this item to Disabled. Save and exit.
  • If the Access IBM Predesktop Area has not been previously disabled, press Enter to load Access IBM Predesktop Area. Then run RECOVER TO FACTORY CONTENTS in Access IBM Predesktop Area.
  • If item 2 failed, press F3 in welcome screen in RECOVER TO FACTORY CONTENTS. Run FDISK, and then delete all partitions. Run RECOVER TO FACTORY CONTENTS in Access IBM Predesktop Area again.
  • If item 3 failed, select CD-ROM boot in Startup in Access IBM Predesktop Area. Boot from Recovery CD and perform full recovery from it.
  • If item 4 failed, replace the hard drive.
  • 1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication
    2000 Hard Drive Active Protection sensor diagnostics failed. Press ESC to continue. Press F1 to enter SETUP.
  • Undock docking station or port replicator if it is attached to the ThinkPad computer, and place the computer on a horizontal surface. Do not apply any physical shock to the computer.
  • Run Diagnostics, select Other Devices then select Hard Drive Active Protection Test.
  • 2010 Warning: Your internal hard drive (HD) may not function correctly on this system.
    Ensure that your HD is supported on this system and that the latest HD firmware is installed.

    If in the primary bay the customer is using a non-IBM, non-Lenovo hard drive, or an old generation IBM hard drive which is not supported by this system, with the risk in mind, the customer can still use it by pressing ESC.

    If in the primary drive bay the customer is using a supported IBM or Lenovo hard drive with an old firmware, then update its firmware to the latest.

    2100 Initialization error on HDD0 (Main hard drive)
  • Reseat the hard drive
  • Main hard drive
  • System board
  • 2102 Initialization error on HDD1 (Ultrabay hard drive)
  • Reseat the hard drive
  • Ultrabay hard drive
  • System board
  • 2110 Read error on HDD0 (Main hard drive)
  • Reseat the hard drive
  • Main hard drive
  • System board
  • 2112 Read error on HDD1 (Ultrabay hard drive)
  • Reseat the hard drive
  • Ultrabay hard drive
  • System board